It is impossible to pass Cisco ccna wireless 200 355 pdf download exam without any help in the short term. Come to Examcollection soon and find the most advanced, correct and guaranteed Cisco cisco 200 355 practice questions. You will get a surprising result by our Renewal Implementing Cisco Wireless Network Fundamentals practice guides.

Q81. Which four levels of messages will be sent to the logging server? (Choose four.) 

A. alerts 

B. critcal 

C. debugging 

D. emergencies 

E. errors 

F. informational 

G. notifications 

H. warnings 

Answer: A,B,D,E 


Q82. Which two statements about the Cisco WLC and AP code upgrade when 7.0 is running are true? (Choose two.) 

A. The AP can download and run new code only after a Cisco WLC reboot causes the AP discovery and join. 

B. The AP can download new code before the Cisco WLC reboot, but only if the AP is configured the CLI via SSH. 

C. The AP can download new code before Cisco WLC reboot if it is configuring the Cisco WLC directly using the GUI via HTTP or HTTPS. 

D. The Cisco WLC defaults to booting newer code, but it can boot older backup code only from the CLI configuration. 

E. The Cisco WLC can boot either primary or backup code configured from the GUI. 

F. The Cisco WLC can download only a single code at a time for reboot. 

Answer: C,E 


Q83. Which two statements about the requirements to configure inter-controller roaming are true? (Choose two.) 

A. The same mobility domain names are configured across controllers. 

B. The same RF group names are configured across controllers. 

C. The same controller hardware version is configured across controllers. 

D. The same AP manager interface is configured across controllers. 

E. The same virtual interface is configured across controllers. 

F. The same controller software version is configured across controllers. 

Answer: A,E 


Q84. Which protocol is used for Cisco WCS to communicate with Cisco WLC? 

A. SNMP 

B. CAPWAP 

C. HTTPS 

D. SSH 

Answer:


Q85. When a wireless guest network is implemented using auto-anchor mobility in a controller-based wireless network, which controller is responsible for a guest client's IP address and their security configuration? 

A. any controller that supports the same VLAN 

B. foreign controller 

C. anchor controller 

D. master controller 

E. RF group master controller 

Answer:


Q86. A help desk engineer is attempting to perform a remote packet capture on the wireless network. Which access point mode is necessary to perform this function? 

A. sniffer 

B. SE-Connect 

C. monitor 

D. rogue detector 

E. FlexConnect 

Answer:


Q87. Refer to the exhibit. 

With the current Cisco WLC version 7.0 syslog level settings set the way they are, which log levels are captured by the Syslog server? 

A. syslog level errors only 

B. all syslog levels 

C. only the syslog severity level number of error and greater 

D. only the syslog severity level number of error and less 

Answer:


Q88. The IEEE 802.11n standard provides 40-MHz channels, improved MAC efficiency, and MIMO. 

Which three elements define the 802.11n implementation of MIMO? (Choose three.) 

A. channel bonding 

B. dynamic frequency selection 

C. maximal ratio combining 

D. packet aggregation 

E. spatial multiplexing 

F. transmit beam forming 

Answer: C,E,F 


Q89. When an AP, in its default configuration mode, connects to a Cisco WLC, which methods are available for remote management access to an AP? 

A. SSL and SSH are available only after configuration by a Cisco WLC version 7.0. 

B. SSH only 

C. HTTPS, and SSH 

D. SSH and Telnet 

E. SSH and Telnet are available only after configuration by a Cisco WLC version 7.0. 

Answer:


Q90. Which statement about the impact of configuring a single SSID to support TKIP and AES encryption simultaneously is true? 

A. The overhead associated with supporting both encryption methods significantly degrades client throughput. 

B. Some wireless client drivers might not handle complex SSID settings and may be unable to associate to the WLAN. 

C. This configuration is unsupported and the Cisco Wireless Control System generates alarms continuously until the configuration is corrected. 

D. This configuration is common for migrating from WPA to WPA2. No problem is associated with using this configuration. 

Answer: