Pass4sure offers free demo for ccnp 300 101 exam. "ROUTE Implementing Cisco IP Routing", also known as cisco 300 101 dump exam, is a Cisco Certification. This set of posts, Passing the Cisco ccnp routing and switching route 300 101 official cert guide exam, will help you answer those questions. The ccnp routing and switching route 300 101 complete video course Questions & Answers covers all the knowledge points of the real exam. 100% real Cisco ccnp dumps 300 101 exams and revised by experts!

P.S. Actual 300-101 preparation exams are available on Google Drive, GET MORE: https://drive.google.com/open?id=1g4kPItyKIZuA3JfCSZX112aKL18D2zfl


New Cisco 300-101 Exam Dumps Collection (Question 15 - Question 23)

Question No: 15

What happens when an IPv6 enabled router running 6to4 must send a packet to a remote destination and the next hop is the address of 2002::/16?

A. The IPv6 packet has its header removed and replaced with an IPv4 header

B. The IPv6 packet is encapsulated in an IPv4 packet using an IPv4 protocol type of 41

C. The IPv6 packet is dropped because that destination is unable to route IPv6 packets

D. The packet is tagged with an IPv6 header and the IPv6 prefix is included

Answer: B

Explanation:

6to4 and Teredo are dynamic tunneling techniques used by desktop operating systems to help their users gain access to the IPv6 Internet. These techniques tunnel the IPv6 packets within IPv4 packets. The 6to4 method places the IPv6 packets within IPv4 protocol 41 packets. The Teredo method places the IPv6 packets within IPv4 packets with a UDP 3544 header.


Question No: 16

Which command enables NAT-PT on an IPv6 interface?

A. IPv6 nat-pt enable

B. ipv6 nat

C. Ipv6 nat-pt

D. Ipv6 nat enable

Answer: B

Explanation: http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipaddr_nat/configuration/15-mt/nat-15-mt-book/ip6-natpt.html


Question No: 17

Which three functionalities are specific to stateful NAT64? (Choose Three)

A. It requires IPv4-transalable IPv6 address

B. It requires either manual or DHCPv6 based address assignment for IPv6 host.

C. It helps ensure end-to-end address transparency and scalability.

D. A state or bindings are created on every unique translation.

E. It conserves IPv4 addresses.

Answer: B,D,E


Question No: 18

A router receives a routing advertisement for the same prefix and subnet from four different routing protocols. Which advertisement is installed in the routing table?

A. RIP

B. OSPF

C. iBGP

D. EIGRP

Answer: D


Question No: 19

Which option to the command service timestamps debug enables the logging server to capture the greatest amount of information from the router?

A. uptime

B. show-timezone

C. year

D. msec

Answer: D


Question No: 20

Which two different configuration can you apply to a device to block incoming SSH access? (Choose two)

A. Option A

B. Option B

C. Option C

D. Option D

E. Option E

Answer: A,E


Question No: 21

Under which circumstance will a branch ISR router contain interface vlan configurations?

A. performing inter-VLAN routing

B. performing 802.1Q trunking

C. performing ISL trunking

D. Ethernet Switch Module installed

E. ADSL WIC installed

F. running Call Manager Express

Answer: D

Explanation:

In smaller offices, a single ISR may be used for a both remote connectivity and inter-VLAN routing. In that case, know that an Ethernet Switch Module would be required for the ISR router


Question No: 22

A network engineer is trying to modify an existing active NAT configuration on an IOS router by using the following command:

(config)# no ip nat pool dynamic-nat-pool 192.1.1.20 192.1.1.254 netmask 255.255.255.0 Upon entering the command on the IOS router, the following message is seen on the

console:

%Dynamic Mapping in Use, Cannot remove message or the %Pool outpool in use, cannot destroy

What is the least impactful method that the engineer can use to modify the existing IP NAT configuration?

A. Clear the IP NAT translations using the clear ip nat traffic * " command, then replace the NAT configuration quickly, before any new NAT entries are populated into the translation table due to active NAT traffic.

B. Clear the IP NAT translations using the clear ip nat translation * " command, then replace the NAT configuration quickly, before any new NAT entries are populated into the translation table due to active NAT traffic.

C. Clear the IP NAT translations using the reload command on the router, then replace the NAT configuration quickly, before any new NAT entries are populated into the translation table due to active NAT traffic.

D. Clear the IP NAT translations using the clear ip nat table * " command, then replace the NAT configuration quickly, before any new NAT entries are populated into the translation table due to active NAT traffic.

Answer: B


Question No: 23

How does an IOS router process a packet that should be switched by Cisco Express Forwarding without an FIB entry?

A. by forwarding the packet

B. by dropping the packet

C. by creating a new FIB entry for the packet

D. by looking in the routing table for an alternate FIB entry

Answer: B


Recommend!! Get the Actual 300-101 dumps in VCE and PDF From Certifytools, Welcome to download: https://www.certifytools.com/300-101-exam.html (New 487 Q&As Version)